AT3 98 HA
Petrol tractor
This 98cm lawn-tractor can either side-discharge or mulch clippings and features a foot-pedal hydrostatic drive. Power comes from a 414cc STIGA engine. Mulching-kit available separately.
- 98 cm cutting deck and strong-built side discharge funnel to manage lawns up to 5200 m2
- Equipped with powerful STIGA single-cylinder engine
- You have a choice among 7 possible cutting height settings, to fit your lawn's needs
- Blades can be easily engaged thanks to PTO electromagnetic clutch
- Comfortable speed management, thanks to pedal-operated hydrostatic transmission
- Enhanced driving experience with ergonomic steering wheel
Product details and specs
Supplied with a 98cm side-discharge cutter-deck, the Alpina AT3 98 HA is a fast and efficient performer over large areas and will take the sort of overgrown grass found in meadows and outlying informal stretches in its stride!
Under the new, design-optimized bonnet is an STIGA ST 400 engine; a 414cc motor that produces an impressive 7.1kW of clean, low-emission power; and which will prove economical and quiet-running.
The foot-pedal operated hydrostatic transmission on the AT3 98 HA confers fantastic maneuverability - you’ll be able to adjust the ground-speed in infinite increments, smoothly slowing down when approaching obstacles, and then accelerating intuitively into long, unbroken passes.
A robust bumper provides reassurance when it comes to front-end impact protection; while a convenient electromagnetic PTO clutch means the blades are activated by simply pushing a button.
The AT3 98 HA benefits from substantial 457mm drive-wheels that ensure non-slip traction on sloping ground and in damp, muddy conditions.
It’s fitted with twin-headlights for safe low-light mowing; and it offers seven preset cutting-heights that will help you to create the sort of finish you prefer. Thanks to its optional mulching capability, the AT3 98 HA is also suitable for use on frequently-mown formal lawns.
Under the new, design-optimized bonnet is an STIGA ST 400 engine; a 414cc motor that produces an impressive 7.1kW of clean, low-emission power; and which will prove economical and quiet-running.
The foot-pedal operated hydrostatic transmission on the AT3 98 HA confers fantastic maneuverability - you’ll be able to adjust the ground-speed in infinite increments, smoothly slowing down when approaching obstacles, and then accelerating intuitively into long, unbroken passes.
A robust bumper provides reassurance when it comes to front-end impact protection; while a convenient electromagnetic PTO clutch means the blades are activated by simply pushing a button.
The AT3 98 HA benefits from substantial 457mm drive-wheels that ensure non-slip traction on sloping ground and in damp, muddy conditions.
It’s fitted with twin-headlights for safe low-light mowing; and it offers seven preset cutting-heights that will help you to create the sort of finish you prefer. Thanks to its optional mulching capability, the AT3 98 HA is also suitable for use on frequently-mown formal lawns.
Technical specs
General info
EAN/UPC
8008984851559
SKU
2T0610404/A22
Power
Battery capacity
18 Ah
Power
7.1 kW
Power source
Petrol
Engine Brand
STIGA
Engine model
ST 400 Powered by STIGA
Displacement
414 cm³
Engine rotation speed
2800 rpm
Battery Voltage
12 V
Choke
Manual
Engine cooling
Air
Fuel tank capacity
6 l
Suggested working area
5000 ㎡
Cutting system
Minimum uncut radius
70 cm
Cutting width
98 cm
Reverse mowing
Yes
Blade rotation
Untimed
Cutting height adjustment
Manual with lever
Cutting height positions
7 positions
Cutting height range
25 - 80 mm
Number of blades
2
Additional cutting method
Mulching
Blade engagement type
Electric
Drive system
Traction
Rear-wheel drive
Transmission
Transmission method
Pedal-operated
Transmission type
Hydrostatic
Equipment
Steering wheel
Alpina ergonomic
Seat type
Alpina smart with low back support
Seat adjustment
Screws
Dashboard
No
Front wheel size
15x6.00-6
Rear wheel size
18x8.50-8
Hour meter
No
Headlights
Conventional
Cruise control
No
Bumper
Yes
Washing link
Yes
Storage compartment
Yes
Cup holder
Yes
Pivoting front axle
Yes
Antiscalp wheels
2
Safety system
Seat with Safety Contact Breaker
Tools kit
Mulching kit
Optional
Battery charger
Optional
Trailer hitch kit
Optional
Vibration and noise data
Guaranteed sound power level (LwA) - dB(A)
100
Max vibration on driver's seat (m/s2)
0.94
Max vibration on steering wheels (m/s2)
3.33
Measured sound power level dB(A)
99
Measured sound pressure level at operator ear dB(A)
86
Overall dimensions
Pack weight
204 kg
Product length
1726 mm
Product width
1200 mm
Product height
1100 mm
Product weight
162 kg
Related Accessories
Support
What is the proper way to clean the lawn tractor after mowing the grass?
The exterior of the tractor mower must be cleaned with water and detergent, paying attention not to get water in the electrical system, motor and circuit board located under the instrument panel. The collection bag should be emptied and cleaned of residue, then remounted so the cutting assembly can be washed, and then removed, rinsed and allowed to dry. When washing the cutting device assembly and the expulsion chute, the collection bag or rear discharge shield must be fitted, the operator must be seated, the cutting device assembly must be in position “1”, the engine running, transmission placed in neutral and the cutting device must be connected. Then connect a water hose to the appropriate pipe fittings and allow the water to flow for a few minutes while keeping the cutting devices in motion.
What action should be carried out before winter storage or before storing it for a period longer than 30 days?
After allowing the engine to cool down and fully recharging the battery, disconnect the battery cables and store it in a cool and dry place. Empty the fuel tank, clean the machine thoroughly, check the condition of the cutting device assembly, and, if necessary, contact the service centre. Then store the lawn tractor with the cutting deck in a lowered position, in a sheltered environment and, if possible, covered with a sheet.
What action should be carried out before initially using a riding tractor that has been stored over a winter or for a period longer than 30 days?
Refuel it and check the oil level, air filter and petrol filter. Check that the tyres are correctly pressurised and then set up the lawn mower tractor according to how you intend to carry out the mowing (side discharge, collection, rear discharge, mulching). For further information about the preliminary operations and safety checks, please refer to the designated sections of the instructions manual.
What standard maintenance operations does the lawn mower tractor need?
Before each use, we recommend that you perform safety and control checks, check the tyre pressure, and replenish the fuel and oil tank, if necessary. After each use, arrange for a general cleaning of the riding tractor. Please refer to the designated section of the instruction manual (“maintenance table”) for the regular actions recommended to ensure optimal use of the machine.
What are the cutting functions of the lawn tractor?
The riding tractor can be set up in different cutting modes: rear bag collection or rear discharge, or mowing and chopping the grass using the special “mulching kit” function. The mulching cutting system allows you to mow the grass into fine particles, which remain on the lawn, restore nutrients and support growth.
What kinds of parts and accessories can the lawn tractor be equipped with?
The lawn tractor can be equipped with various parts and accessories to increase its functions and ensure maximum versatility all year round. For the complete list of parts and accessories, please refer to the relevant product page on the website.
Reach Information
Information on Article 33 of REACH Regulation concerning STIGA Group products. Discover moreReach Information
AT3 98 HA
| 382722475/0 | PC BOARD SD (ISO) Waterwei | Lead | 7439-92-1 | ||||||||
| 118120007/0 | BATTERY 12V 18AH [HAIJIU] | Lead | 7439-92-1 | ||||||||
| 382004618/0 | DECK ENGAGE CABLE | Lead | 7439-92-1 | ||||||||
| 118400919/2 | TRANSAXLE HYDRO-GEAR T2 | 1) SEALANT MATERIAL : Octamethylcyclotetrasiloxane 2) PLUG 9/16-18 METAL: Lead 3) ROD BYPASS .375 X 3.81: Lead 4) CHK PLUG ASSY/WASHER,.027": Lead 5) CHK PLUG ASSY/WASHER,.027": Lead 6) FITTING 5/16 SAE, 5/32 TUBE: Lead | 1) 556-67-2 2) 7439-92-1 3) 7439-92-1 4) 7439-92-1 5) 7439-92-1 6) 7439-92-1 | ||||||||
| 125601577/0 | PULLEY | Lead | 7439-92-1 | ||||||||
| Component 1 | Component description 1 | Substance/s | CAS number | Component 2 | Component description 2 | Component 3 | Component description 3 | Component 4 | Component description 4 | Component 5 | Component description 5 |
|---|
Related Products
Write Your Own Review